Skip to main content

During Atheltic rubber track construction,how to avoid rain ?

 I believe that many constrution teams  meet this problem.Just after the construction of tartan track,it was drenched and even soaked by the sudden heavy rain.Apart from worrying, there was no remedy.



According to years of experience, there are two ways to deal with rubber track that are drenched by rainwater.

1. The rubber track cannot be completely cured after being exposed to rain. This kind of treatment is more troublesome. The incurable part must be completely shoveled off, and then thoroughly polished until the underground cement foundation is exposed, and then restart according to the process. Although it is a waste of materials and labor, this is the only more thorough solution without any sequelae.

2. The athletic running tartan track can be cured after being exposed to rain, but there are many small pits on the surface that are smashed by raindrops, and there may be bubbles in some places. To deal with this situation, first use a knife to cut off the bubbles and use PU material is divided into several times to fill up the bubbling, and then use an grinder machine to polish the small pits as far as possible, even if there is a slight unevenness after the grinding, it does not matter, and finally a thin layer of PU material is used to make up It can be flat.



Pay attention to rain prevention during construction

　　 There are certain conditions during the construction of the oval running track project. For example, the surface temperature during construction should be in the range of 15 to 45 centigrade, and the weather should be sunny, fog-free, and relatively humid. In order to ensure the quality of the entire rubber athletic track project, the construction personnel must follow these conditions during the construction process to prevent the project from failing to achieve the expected results. Here I would like to remind you that water cannot be added to the rubber track materials during the construction process.

During the construction of the athletic track, water and rain should be avoided as far as possible, because the athletic track is a kind of polyurethane rubber material. After laying the rubber surface , there will be blistering and shelling, because the density of the base course of the rubber track is not controlled reasonably. Therefore, it is necessary to strictly control the density of the rubber track, so as to prevent shelling and shelling because the asphalt foundation layer itself is not compacted, and the surface of the oval track is gasified, and even the foundation surface is broken in serious cases.

During the construction period, plastic film should be equipped to listen to the weather forecast at any time. In case of rain during the construction, stop work immediately to cover the plastic film on the the surface .

Labels

Labels:

Comments

Post a Comment

Popular posts from this blog

Standard Basketball Court Size

  1. The playing   basketball court is 28 meters long and 15 meters wide. The ratio of long money: 28:15. The area of the competition area is 28*15=420 m2. 2. Line: The width is 0.05 meters (5 cm).     Boundary: The court boundary is at least 2 meters away from spectators, billboards or any other obstacles. The boundary on the long side of the court is called the sideline, and the boundary on the short side is called the endline. 3. Free throw line, restricted area and penalty area: the area of the three-second zone = (3.6+6)*5.8/2=27.84m2 1. The free throw line should be parallel to the end line, and its outer edge is 5.80 meters away from the inner edge of the end line; this line is 3.60 meters long. Its midpoint must fall on the imaginary line connecting the midpoints of the two end lines. 2. The ground area formed by drawing two lines from both ends of the free throw line to 3 meters from the midpoint of the end line (both measured from the outer edge)...
Post a Comment
Read more

How to choose materials for the gym floor?

  The choice of floor materials is often the easiest to be overlooked in the gym decoration design, but the choice of floor materials is very important for a gym. Gyms are generally indoors. Although the choice of floor materials does not have any effect in the decoration, But for those who come to exercise, the impact is still great.   The gym floor uses a variety of materials, such as solid wood flooring, composite flooring, rubber wood flooring, laminate flooring, solid wood composite flooring , thin carpets, PVC vinyl  flooring,artificial grass,rubber mat etc.   However, many people experience knee and foot pain and leg pain after fitness. This is caused by the poor shock absorption effect of the gym. A good gym floor needs to have the characteristics of strong impact resistance, good elasticity, waterproof and anti-skid.  Therefore, the choice of floor in the gym decoration is also very important. The following types of floor materials can be selected reaso...
Post a Comment
Read more

Why does PVC floor warp?

  Many consumers may experience warping when using PVC flooring. When the cardboard is warped, consumers can determine that this is a flooring quality problem, and exactly what causes the PVC flooring to warp. 1. because the poor quality, it will cause warpage problems. The structural stability of PVC floor is poor, and it is easy to shrink or expand at the alternating temperature of cold and heat, so it is easy to warp. The PVC floor production standard of the regular manufacturer, the floor quality is guaranteed, durable, and can reduce the chance of warping. 2. Architectural attachments can also lead to floor edges. PVC floor surfacing accessories are often used in latex, double-sided tape and pit knife glue. High-quality glue can make the floor and the ground stick together, and it is also very waterproof. If the glue is not good, it is easy to cause the floor to be weak and easy to bend. Of course, construction quality should not be ignored. Specialized construction personnel ...
Post a Comment
Read more